Well Water Suddenly Stopped Working

If you are experiencing no water from the well, there can be many low water pressure causes, including a failing well pump, stuck check valve, partially closed or bad gate/ball valve, and leaking/failing pressure tank.

Why would a well suddenly stop working?

It could be a broken water line from the well to the house — usually you'll have a wet area between the well head and the house — a bad check valve just above the submersible pump at the bottom of the well, a bad connector leaving the well casing or even a broken water line inside the well casing.

How do I reset my well pump?

Hold the reset lever in the start position until the pressure builds up and the gauge reads over 40 PSI; then let it return to the AUTO position. The pump should now run on its own and continue until the pressure reaches the cut out setting, (usually between 50 - 60 PSI), and then shut off.

What are the signs that a well pump is failing?

Low water pressure is usually one of the most obvious signs that your well pump isn't working properly. However, you might also notice fluctuations in the pressure. Other things can also cause water pressure changes, though, so you might need a plumber or well service provider to determine the cause.

Why would I suddenly have no water?

If you're not getting any water in your home, it's likely because of a problem with the water main. If you have an emergency shut-off valve, it could have accidentally triggered and stopped your water flow, or the valve could be open and impeding your water supply because it's leaking.

Can a well suddenly go dry?

If a well runs dry, is it permanent? When a well “runs dry” it doesn't mean that the well will never produce water again. Aquifers can recharge through a combination of more precipitation and less pumps pulling water out of that aquifer. Sometimes wells can run dry permanently, but that is quite uncommon.

Why is my water pump not turning on?

Check that the pressure control switch is not stuck Tip: Try tapping on the water pressure control switch. If the pump turns on then it may be debris clogged. Burned control relay points in the pressure switch may also prevent good electrical contact and can make the pump switch behave erratically.

Is there a breaker on a well pump?

Most submersible well pumps are single phase 230 volts and require a 2 pole circuit breaker (2 individual circuit breakers connected together).

How many years do well pumps last?

The average lifespan of a well pump is generally around eight to 15 years. However, where your pump will fall in that pretty wide age range depends on many factors. The single largest factor in your pump's life expectancy is the frequency of your pump's duty cycle.

What to do when well pump stops working?

Check the circuit breaker connected to the well and see if there is a short in the system. If your well pump stopped working after a thunderstorm, check to see if the well was struck by lightning. If there is a short or surge in the power to your well, the circuit might have blown.

How much does a new well pump cost?

The average cost to replace or install a new well pump is typically between $1,000 and $2,750, with the national average being about $1,750. The type of well pump you install or replace can greatly change both the unit cost and the installation cost.

What are the 3 ways a water pump can fail?

THE MOST COMMON DAMAGE TO A WATER PUMP: CAUSES AND CORRECTIVE ACTIONS

• IMPROPER USE OF SEALS/GASKETS OR SEALANT.
• BAD OR WRONG COOLANT.
• DEFECTIVE OR IMPROPERLY INSTALLED BELT DRIVE COMPONENTS.

How do you check a well pump?

How do you check your well tank's pressure?

1. Cut the power to your well tank. Make sure that you shut off your well's submersible pump to prevent it from starting.
2. Drain the well tank. ...
3. Locate a pressure gauge. ...
4. Use the gauge to check the tank's pressure. ...
5. Adjust the pressure with an air compressor if necessary.

Is no running water an emergency?

Lack of water is a strong maintenance emergency. It's possible this can be from a broken main supply line. The local utility should be able to institute a repair immediately, if you raise the alarm.

Why is there no water pressure in my well?

The cause could be clogged pipes or a clogged well casing from a buildup of sediment and minerals. It could also be an improperly placed well pump. If the pump is placed too close to the top of the well's water level, it will reduce water flow.

How do you reset a well pump after a power outage?

Some pressure switches may need to be reset after a power outage. This is usually an easy task and all you need to do is turn the lever to “auto” and hold it until the pump turns on and the pressure gauge reads 30psi.

How do I get my water pump to work again?

We've put a quick guide together to help you through the basic steps of priming your water pump.

1. Make sure the power is turned off.
2. Gain access to the pump system. ...
3. Check for damage. ...
4. Test a hose. ...
5. Open the relief valves. ...
6. Attach the hose. ...
7. Turn on the water and wait for it to enter the tank. ...
8. Turn the power on.

Do well pumps automatically shut off?

Your well pump is designed to shut off once it reaches a certain pressure. A significant leak anywhere in the well piping lowers the water pressure in the system. So if the pressure is too low, your pump won't shut off and instead will continue running all the time.

How do I turn my well water back on?

Down if you find this to be hold up on this switch. Until you hear the pump start and continue to

What would cause a well pump breaker to trip?

One common cause of a submersible pump tripping its breaker can be cracks or leaks in the housing. If your pump's housing is cracked, water could be getting into the pump through these cracks and causing it to short circuit. The same can be happening if you have a leak in your pump which is letting water in.